FAQs

Garage doors are made of a variety of materials, depending on the type of door you’re looking at.

Most steel garage doors are made with galvanized steel, which has a zinc coating that prevents rust and corrosion. Some steel garage doors are powder-coated or painted to give them a more durable finish.

Wood garage doors can be made from different types of wood, including cedar, redwood, and pine. They may also have a protective clear sealant applied to protect them from weather damage.

Garage doors can also be made from aluminum or fiberglass composite materials, which are lighter than steel but still durable and safe for use in garages.

Sectional Doors: These doors are made up of several separate panels that are joined together to form one large door. Sectional doors are often used for garages with high ceilings and can be particularly useful in garages where space is limited.

Tilt-Up Garage Doors: Tilt-up garage doors are made up of two pieces – the top section that tilts up, and the bottom section that stays fixed in place. Tilt-up garage doors can be used for both residential and commercial applications, though they tend to be more common in residential settings.

Rolling Steel Garage Doors: Rolling steel garage doors are available in both single-slide and double-slide configurations. They are generally more durable than other types of steel garage doors because they have fewer moving parts than other types of steel garage doors. This type of garage door is often used by homeowners who want a more traditional look for their homes or businesses.

Garage doors are often the largest source of heat loss in a home. In fact, a garage door left open can lose up to 100% of the heat generated by your furnace or water heater.

The insulation value of your garage door is determined by its R-value, which measures how well it resists heat flow. The higher the R-value, the better it insulates you against the elements.

EDM Garage Doors offers insulated steel doors that feature an R-value of up to 22, making them ideal for keeping warm air inside during winter months and hot air outside during summer months.

Your pre-finished steel garage door is easy to clean, but you’ll want to make sure you have a few supplies on hand before you begin. First, get a bucket and fill it with warm water, then add one cup of mild liquid detergent and mix until the soap has dissolved. You can also use an all-purpose cleaner or a degreaser, but be sure to check the label for any warnings about using them on your garage door before you start.

Next, grab a soft cloth (a microfiber towel works great) and dip it into your cleaning solution. Wring out any excess liquid before wiping down your garage door. Use short strokes while moving horizontally across the surface of your door; this will help prevent streaking or water spots from forming as you go. 

If there’s dirt stuck in between crevices and joints, use a toothbrush or other small brush to scrub those areas thoroughly until they’re clean! Once everything looks good as new, rinse off your door with fresh water and dry it off with another clean towel before storing away for next time!

When it comes to cleaning your wooden garage door, there are a few things to keep in mind.

First, you’ll want to make sure your garage door is free of all debris. This means sweeping the floor and removing any dirt or debris from around the base of the garage door.

Next, you’ll need a bucket of warm water and mild dish soap. The soap will help break down any grease or grime that may have accumulated on the surface of your garage door. For best results, use a soft-bristled brush or sponge to apply the soapy water and scrub your garage door clean.

Finally, rinse off with warm water and dry with a clean towel before applying any WD-40 or other protective coating on top of it!

To match your home’s color, you can use exterior latex paint designed for steel garage doors. You should also use a high-quality brush and roller to ensure the best application possible.

It is important to keep in mind that pre-finished steel garage doors have a special coating on them that protects against rust and corrosion. This coating is what gives the door its unique finish, but it also makes it difficult to paint.

You will need to strip off this coating before painting so that you can get an even finish. To do this, use a chemical stripper or sandpaper. After stripping off the coating, clean the surface with soap and water before painting it with your chosen color!

The frequency of servicing your overhead garage door depends on the model you have. If it’s a standard, steel-and-aluminum garage door, we recommend checking the tracks on a monthly basis and lubricating them with WD-40 or silicone spray. Check for dents that might be causing the door to stick as well.

If you have a fiberglass door, you’ll want to check for cracks and chips every six months. Don’t forget to check the weatherstripping, which should be replaced annually!

Longer than you think.

The average life expectancy of a garage door spring is between 10 to 15 years. But they can last longer, sometimes up to 25 years. If you are getting a new garage door, it is best to replace your springs as well so that you don’t have to worry about them for another few years.

There are two ways to open a garage door manually:

1. The first way is to lift the door up by hand. To do this, you will need to hold down the red button on your remote control for at least 5 seconds, or until you hear a series of beeps. When you release the red button, your remote will beep again. This tells you that it has been successfully disabled. The next time you use your remote control, it should work as normal.

2. The second way is to use a screwdriver to remove one or two screws on the back of your garage door opener. Once these screws have been removed, pull out the cover plate and expose several wires. Use an insulated wire stripper tool to cut off each of these wires (be sure not to cut any others). 

If there is no cover plate on your garage door opener (like on older models), then access these wires through a small hole in the wall near where they come out of the ceiling or floorboards – but don’t cut these wires! Then replace all three parts (cover plate/screws/wires) before trying again with your remote control.

There are a few things you can look for to tell if your garage door spring is balanced properly. First, check the curve of the springs in relation to each other. If one is lower than the other, or if there is a gap between them, then they are probably not balanced. 

Next, look at the springs themselves. If they’re bent out of shape or if there are any tears in them, then they need to be replaced. Finally, look at the tension on both sides of the door. If one side has more tension than another, then it’s probably not balanced correctly either.

If you notice any of these indicators—or if you want to check that your garage door springs are still working properly after installing new ones—then contact us today!

It’s possible that your garage door is not level, which is a common issue. If your garage door is not level, it will not work properly. Another possibility is that the springs are broken or missing. If this is the case, you will need to replace them before using your garage door again. 

Another common problem with garage doors is blocked sensors which prevent them from working properly. If your sensors are blocked, try cleaning them with water or soap to see if they will work again or if they need to be replaced altogether.

Garage doors are a major part of your home, so it’s important to keep them in good condition. There are several simple things you can do to keep your garage door and opener running smoothly.

First, check for loose screws or bolts on the hinges, tracks, and rollers. If these parts are loose or damaged, they will need to be replaced.

Next, check the cables that lift the door. These cables should be taut and not frayed or broken. If they’re frayed or broken, it’s time for new cables.

Finally, make sure that your automatic garage door opener is properly aligned with its track so that it doesn’t get stuck when closing or opening the door.

Choosing a garage door dealer can be overwhelming. There are so many options, and you want to ensure you choose the right one for your needs. At EDM Garage Doors, we believe that our customers deserve better than just another garage door company—we want them to have an experience that’s as good as it gets. 

• A dedicated team of representatives who are ready to answer any questions you have about our services.

• A wide variety of products—including roll-up doors, sectional doors, and more—so that you can choose exactly what you need for your home or business.

• The ability to schedule an appointment online means that we show up on time every time (and don’t waste your time).

When you choose EDM Garage Doors as your garage door dealer, you can be sure that we’ll be there every step of the way—from design consultation through installation and maintenance—to ensure that your garage door project is a success!